Perforated vs. Expanded Mesh vs. Decorative Mashrabiya: Choosing the Right Architectural Screen
Contents11 sections
- What Should a Screen Facade Actually Do?
- How Does Perforated Sheet Control View and Light?
- What Does Expanded Mesh Give That Perforation Cannot?
- Where Does a Mashrabiya Screen Still Win?
- Which Screen Type Handles Dust and Sand Best?
- Why Do Laser-Cut and Punched Panels Allow 10 mm Flatness?
- Which Grade and Thickness Should a Coastal Screen Use?
- How Is a Screen Panel Fixed and Jointed?
- What Panel Size Limits Apply to Screens?
- What Must Be Approved at Sample Stage Before the Screen Is Released?
- Frequently Asked Questions
Screen facade selection and DFM review for perforated and lattice screens.
Choose a screen by what it must block, not by pattern. Perforated sheet controls view through hole size and pitch; expanded mesh reads as depth; mashrabiya profiles give the strongest shadow line. Laser-cut and punched panels run 0.3–3.0 mm thick with flatness to 10 mm; in coastal air specify 316L (PREN about 25 versus 19 for 304).
What Should a Screen Facade Actually Do?
A screen is a filter, not a wall. It stands between a room and the weather and has to answer four questions at once: how much view is kept, how much sun is cut, how the surface reads from thirty metres, and how it is cleaned in service. Pattern is the last of those decisions, not the first, because two patterns with the same open area can behave completely differently.
Three families are routinely confused at tender stage. Perforated sheet is a solid sheet with holes cut through it. Expanded mesh is a solid sheet slit and stretched into a diamond lattice, so no material is removed. Mashrabiya is an assembled lattice of profiled bars with real depth, built from a drawn geometric pattern rather than cut from a single sheet.
| Type | How it blocks | Light and shadow | Structural depth | Climate fit | Cleaning | Relative cost |
|---|---|---|---|---|---|---|
| Perforated sheet | Holes cut in a solid sheet; view is set by hole size and pitch | Flat graphic at distance; shadow is a copy of the hole | None beyond sheet thickness | Hot-dry and hot-humid; salt air needs 316L | Blow out, then wash; hole edges hold dust | Medium |
| Expanded mesh | Slit and stretched lattice; closes and opens with viewing angle | Layered, because strands sit at two levels | Strand depth only | Good ventilation; suits hot-dry screens | Easiest; dust passes or sits loose on strands | Low |
| Mashrabiya | Assembled profile lattice with real cavity depth | Deepest shadow line; pattern reads in relief | Profile depth, set by design | Hot-dry; the deep screen shades the glass behind it | Hardest; dust settles on the profile shelves | High |
MetalMagus(杭州新恒裕不锈钢制品有限公司)produces all three families as stainless steel facade elements, but they are not interchangeable, and the parameters that apply to one do not transfer to the others. That distinction runs through the rest of this comparison.
How Does Perforated Sheet Control View and Light?
Perforation controls view through geometry, not through pattern names. Three variables do the work: hole diameter, centre-to-centre pitch, and whether the holes are straight or staggered. Open area is the ratio of hole area to panel area, and that is the number to argue about — not the pattern reference.
The same open area can produce two different screens. Many small holes on a tight pitch read as a texture at five metres; the eye stops resolving individual holes and the surface looks like a grey veil. Fewer, larger holes on a wide pitch keep their edges readable at the same distance and give a view with a graphic overlay. One shows shapes; the other silhouettes.
That is why a perforated screen is specified by view line first. If a seated occupant must see the street, the holes have to be large enough and the pitch wide enough at eye height; if the screen only has to cut glare while keeping air moving, a finer pitch does the job with less view. Open area and its effect on shading are calculated per project, available on request — they are not catalogue values.
Perforated panels are also the family that tolerates pattern change most cheaply after approval, because the pattern lives in the cutting file. That flexibility is the reason this family carries most of the custom work in the 22-process matrix.
What Does Expanded Mesh Give That Perforation Cannot?
Expanded mesh is made by slitting a sheet and pulling it open. Nothing is removed, so the finished panel keeps the corrosion behaviour of the parent sheet and loses weight per square metre against solid material of the same thickness. The lattice also has depth: each strand sits slightly out of plane from its neighbour, which is why light through mesh arrives in layers rather than as a flat graphic.
The practical consequence is a screen that changes with the viewing angle. Walk past a mesh facade and it closes and opens by itself — nearly solid at a shallow angle, transparent when you stand square to it. No perforated pattern reproduces that, because a hole is a hole from every direction — which is why expanded metal mesh facade work is specified by strand geometry rather than by open area.
That property is an asset on a car park or a plant room and a liability on a room that needs a fixed view line. It also changes how the screen is drawn: mesh is specified by strand width, strand pitch and overall mesh thickness, and the result depends on which way the diamond runs on the elevation.
Expanded mesh does not appear in the 22-process parameter matrix, so there is no flatness figure, no Ra value and no colour-difference figure to quote for it. Where a project needs those, they are calculated per project, available on request, and written into the specification as project values rather than catalogue values.
Where Does a Mashrabiya Screen Still Win?
Mashrabiya wins wherever the screen is architecture rather than a filter. The form is a lattice of profiled bars with a real cavity behind the face, so a deep profile throws a shadow that no flat sheet can produce: the pattern reads at noon, softens through the afternoon, and disappears at dusk. On a hotel entrance or a cultural building in the Gulf, that behaviour is the design intent, not a by-product.
It is also the only one of the three that carries a regional language. A client asking for mashrabiya is usually asking for continuity with a building tradition, and a flat perforated copy of the same geometry reads as a copy at close range because it has no depth.
The costs sit in assembly and coordination. A mashrabiya screen is many parts with many joints, each of which has to align, and the pattern has to arrive as a drawing rather than a reference photograph. A geometric tradition is shared; a specific drawn pattern belongs to whoever drew it, so the maker needs the designer's file, not a magazine image.
Like mesh, decorative mashrabiya screens sit outside the 22-process matrix. Thickness, flatness and finish values are project values, and structural behaviour over a large opening is calculated per project.
Which Screen Type Handles Dust and Sand Best?
In hot climates the maintenance variable is dust, not rain. Rain washes a facade; dust does the opposite — it settles where air slows down, which on a screen means every edge, shelf and recess.
Expanded mesh is the easiest of the three to keep clean. Dust either passes through the lattice or sits loose on a strand, and a low-pressure air line moves it. There are no blind pockets, because the mesh has no continuous face.
Perforated sheet sits in the middle. The face is flat, so most of it wipes clean, but every hole has an edge, and in fine dust that edge holds a ring. A dense small-hole pattern with a tight pitch accumulates more edge per square metre than an open pattern, which is one reason a fine texture costs more to maintain than it costs to buy.
Deep mashrabiya is the hardest. The profile shelves are horizontal, the cavity is shaded, and dust that lands inside the pattern is not reached by rain or by a window pole. On a large screen this becomes a scheduled cleaning item with access equipment, and it should be priced at design stage rather than discovered after handover.
This belongs in the maintenance specification, not in the buy schedule.
Why Do Laser-Cut and Punched Panels Allow 10 mm Flatness?
Flatness on a perforated panel is a consequence of how it is made, not a concession. Cutting thousands of holes releases residual stress in the sheet, and the panel moves. A dense pattern on a 1,500 × 3,000 mm sheet will bow more than a solid sheet, so the matrix sets flatness at 10 mm Maximum for laser cutting and artistic perforation rather than the 3 mm Maximum used for the mechanical finishes.
This is the distinction that most often goes wrong: a designer writes 3 mm because that is the number on a flat facade panel, and every perforated panel on the job then fails inspection against a criterion written for a different process.
The same logic explains why Ra and colour difference are marked N/M — not measured — for these two processes. On a perforated screen the pattern is the variable that decides how the surface reads; roughness and colour are not the acceptance criteria, so a Ra figure or a ΔE clause would be measuring something the product does not promise. N/M is a specification statement, not a gap in the data.
| Type | Matrix row | Flatness | Ra | ΔE (batch to batch) | Thickness | Width |
|---|---|---|---|---|---|---|
| Laser-cut screen | Row 21 — laser cutting | 10 mm Maximum | N/M | N/M | 0.3–3.0 mm | 10–1500 mm |
| Punched screen | Row 22 — artistic perforation | 10 mm Maximum | N/M | N/M | 0.3–3.0 mm | 10–1500 mm |
| Expanded mesh | Not in matrix | Project value | Project value | Project value | Project value | Project value |
| Mashrabiya lattice | Not in matrix | Project value | Project value | Project value | Project value | Project value |
The last two rows are not a data gap, and the matrix values that do exist are listed on Surface Processing & Finishes. Expanded mesh and mashrabiya are assemblies rather than sheet finishes, so their acceptance values are written for the project, on the drawing, and approved on the sample. Carrying a 10 mm figure across to a mashrabiya lattice because both are "screens" would be exactly the cross-process substitution that causes disputes at inspection. That is the check MetalMagus, an architectural stainless steel systems manufacturer, applies to every screen drawing it reviews.
Send your elevation and we will return a DFM review of the pattern, the module and the fixing before anything is cut. — Send Your Screen Elevation for a DFM Review
Which Grade and Thickness Should a Coastal Screen Use?
For a coastal screen, specify 316L (EN 1.4404). Its molybdenum content lifts PREN to about 25 against 19 for 304, a six-point gap, and the reason the grade changes on a coastal screen. The reason this matters more on a screen than on a wall is geometry: a screen has edges, holes, strands and cavities where chloride deposits collect and where rain does not wash them away. Every one of those features is a place where a lower grade will show tea staining first.
Thickness runs 0.3–3.0 mm across the sheet range, and the choice is driven by what the panel has to do structurally rather than by appearance. A screen that spans between supports, or that doubles as fall protection, needs a structural design and a deflection check; those are calculated per project, available on request, and must come from the engineer of record.
304 is the correct choice for inland and low-chloride sites, and it keeps the cost down without a visible trade-off. 201 is also available, and on a hot-dry inland project it can be worth reviewing, but the environment has to be confirmed with us before it goes into a specification — we do not put 201 into coastal work.
At MetalMagus, an architectural stainless steel systems manufacturer, grade does not change which finishes are available. What it changes is how long a decorative effect survives, so grade and surface belong in the same review.
How Is a Screen Panel Fixed and Jointed?
Two fixing families cover most screen work. Framed cassettes on a carrier rail give a consistent joint and allow a panel to be removed without disturbing its neighbours; direct-fixed panels on standoffs give a thinner edge and a shadow gap, at the price of more careful shimming. The choice is set by how the screen is serviced.
Joints matter more on a screen than on a wall, because light comes through the screen and the building behind it. A gap that measures 8 mm against a dark interior reads as 12 mm at noon against the sky, so the drawing has to carry the joint width, the permitted variation and the direction of alignment — horizontal joints aligned to the module, vertical joints stacked, or both.
Tolerances are the other half of that. Sheet thickness is held to ±0.01 mm and width and length to −0/+0.2 mm, which means a nominal 20 mm joint cannot close to 18 mm through material variation alone. If a joint has to be tighter than those tolerances allow, it is a different detail, not a tighter instruction.
What Panel Size Limits Apply to Screens?
Every screen MetalMagus cuts starts from the same custom stainless steel fabrication range as its other products, shared with honeycomb facade panels: 0.3–3.0 mm thick, 10–1500 mm wide, 300–6000 mm long, with 1,500 × 6,000 mm as the standard full sheet. Cutting a screen from a full sheet reduces the number of joints per elevation, which usually improves the result, because every joint on a screen is visible from both sides.
Where the elevation is larger than a sheet, the module has to be set from the openings outward rather than from the sheet size. A module chosen to divide the sheet evenly will drift at every door and window, and the correction ends up as a narrow filler panel at the far end of the elevation.
There is also a packing limit. Panels ship as PVC film, waterproof paper and a wooden case, fire rating A1, and the crate geometry becomes the real constraint on module once a panel passes the handling weight of the site. A module that is beautiful on the drawing and unshippable in a case is not a module.
What Must Be Approved at Sample Stage Before the Screen Is Released?
The sample has to be full size in at least one direction. A 300 mm square proves the pattern, not how the screen reads at five metres, which is the whole design intent. Approve a panel at the real pitch, held at the real viewing distance, in the real light.
Five things belong on the approval sheet. The pattern file and its hole or strand geometry. The flatness reading against 10 mm Maximum for cut panels. The joint width and the fixing type. The grade certificate with the heat number. And, where a decorative finish is applied, a physical colour reference, because PVD colour is held within 1.0–1.5 ΔE batch to batch and a photograph cannot settle that.
Keep a cut piece of the approved panel. On a screen, the piece that matters is the edge — how the pattern terminates at the border, whether a half-hole is cut or left, and how the corner closes. Those three details are the ones that decide whether the delivered screen looks like the drawing.
Frequently Asked Questions
Is perforated sheet or expanded mesh better for a hot climate?
Neither is better in the abstract; they fail differently. Perforated sheet gives you a predictable view line and a flat face that wipes clean, which suits a screen in front of occupied rooms. Expanded mesh ventilates better, weighs less for the same sheet thickness, and closes and opens with the viewing angle, which suits plant rooms and car parks. Decide by what the space behind the screen has to do, then pick the pattern.
Can I copy a mashrabiya pattern into perforated steel?
You can, and it will read as a copy at close range. A mashrabiya lattice has cavity depth, so its shadow is cast by the profile; a perforated sheet has no depth, so the same geometry becomes a flat silhouette. It works at distance and in profile lighting, and it fails where people walk past at arm's length. If the depth is the point, the depth has to be built.
What open area should a perforated screen have?
Open area follows from the brief rather than from a rule: how much view must survive, how much sun must be cut, and how much the pattern must read from the street. Two panels with identical open area can look and behave completely differently if the hole size and pitch differ. We calculate open area and its shading effect per project and put the number on the drawing, available on request.
Why is flatness different for perforated panels?
Because cutting releases stress. A solid sheet can be held to 3 mm Maximum, but a sheet with a dense pattern will bow after cutting, so laser cutting and artistic perforation are specified at 10 mm Maximum. Writing 3 mm on a perforated panel produces a failure at inspection that no amount of care in production can prevent. The 10 mm figure is a process value, not a relaxation.
Does a screen need 316L if the wall behind it is 304?
In coastal air, yes. Chloride settles in holes, strand gaps and profile cavities where rain does not reach, so a screen collects more aggressive deposits than a flat wall and holds them longer. 316L has a PREN of about 25 against 19 for 304; the six-point gap is why the grade is specified rather than the finish. Using 304 behind a 316L screen on the same facade is the combination that shows tea staining first.
Can a screen be made from 2B sheet?
2B is a mill substrate, not one of the 22 decorative processes, so it carries no flatness, Ra or colour figure in our matrix. Screens are normally cut from 2B or BA stock and then finished, and the finish identity is what the specification should name. If the screen is left as bare 2B, say so on the drawing, because it will be inspected as a mill surface, not as a decorative one.
How thick should a screen panel be?
Between 0.3 and 3.0 mm, with the choice set by the span, the fixing type and whether the screen has a structural role. A decorative infill panel in a framed cassette sits at the thin end; a panel spanning between supports or acting as fall protection needs an engineer's deflection check and usually moves up the range. Structural values are calculated per project, available on request.
Can a screen panel be curved?
Curved screens are formed after cutting, and the question at design stage is what happens to the pattern on the curve. A pattern stretched over a radius opens on the outside and closes on the inside, so hole pitch changes across the panel unless the flat pattern is pre-compensated. Radius, achievable pitch and whether the pattern distorts are project values; send the elevation and we will confirm on the drawing.
What is the largest screen panel you can supply?
The sheet range runs to 1,500 mm wide and 6,000 mm long, and that is the practical limit for a single flat panel. Above that the elevation is divided into modules, and the module should be set from the openings outward so that joints do not drift at doors and windows. Packing usually constrains the module before the sheet does, because panels ship in wooden cases.
What should be on the sample approval sheet?
Five items: the pattern file with hole or strand geometry, the flatness reading against the 10 mm Maximum for cut panels, the joint width and fixing type, the grade certificate with heat number, and a physical colour reference where a decorative finish is applied. Add the edge details — half-hole at the border, corner closure — and keep a cut piece of the approved panel as the reference for site.
A screen is decided on a sample, not on a render. — Request a Finish Sample Kit



