Experts in high-end stainless steel for architectural aesthetics and spatial art solutions.

Home / All / Specification & Selection / Minimum Order, Tooling and Sample Fees for Architectural Stainless Projects

Minimum Order, Tooling and Sample Fees for Architectural Stainless Projects

Nov 3,2026
Contents11 sections
Quick Answer

Three charges sit in front of an architectural stainless order: the sample, any new tooling, and the minimum order. Sampling is free with freight collect; tooling is quoted once per pattern and only where a pattern or profile is non-standard; minimum order starts at 50 sheets. Panels run 0.3–3.0 mm thick, to 1,500 mm wide, A1 fire rated.

50 sheetsMinimum, per specification
20 daysStandard production, working days
48 hSample production
A1Fire rating, EN 13501-1

What Actually Drives the Minimum Order on an Architectural Stainless Project?

A minimum order is not a sales threshold. It is the smallest run at which a finishing line and a forming line can be set up and still produce consistent panels at the specified gauge.

Three physical limits sit underneath it. The first is coil and sheet availability at the gauge you need: architectural work runs from 0.3 mm to 3.0 mm, and a 3.0 mm sheet cannot be finished on a line calibrated for 0.8 mm without a separate pass. The second is yield loss on forming, which is proportionally larger on short runs. The third is colour and gloss consistency, which is only controllable within one finishing batch.

That is why 50 sheets is the floor rather than an arbitrary number. Below that, setup cost per panel rises faster than any buyer will accept, and the batch becomes too short to hold a stable surface across the whole delivery.

Width and length change the arithmetic. A sheet at 1,000 × 2,000 mm covers 2 m²; the same count at 1,500 × 3,000 mm covers 4.5 m², so fifty sheets is 100 m² to 225 m² of finished surface.

Which Three Costs Are Quoted — and Which of Them Is Free?

Three lines appear before production: sampling, tooling, and the order itself. MetalMagus(杭州新恒裕不锈钢制品有限公司) quotes them separately because they are triggered by different things and are not interchangeable.

The sample line is free. What the buyer pays is the freight, on a collect basis, because the courier account and the destination are the buyer's, not ours. The tooling line appears only when a pattern or a profile does not exist yet. The order line is the material and the processing, calculated on the finished panel. Standard production ships in 20 working days; the exact date is confirmed against each order.

Table 1 — What triggers each charge, and where it is confirmed
ChargeWhen it arisesHow it is calculatedCredit on repeat orderConfirmed byConfirmed at
SamplingSample issued before production — 48 hours to produce, 3 days to dispatchNo charge for making the sample; freight collectNot applicableProject Management OfficeSample request
Tooling — embossing rollerOnly where the texture is a new patternQuoted per pattern, charged onceNot stated here — agreed per projectAdvanced Fabrication HubDrawing review
Tooling — etch film or screenOnly where the artwork is newQuoted per pattern, charged onceNot stated here — agreed per projectAdvanced Fabrication HubArtwork approval
Tooling — perforation dieOnly where the hole shape is non-standardQuoted per pattern, charged onceNot stated here — agreed per projectAdvanced Fabrication HubPattern sign-off
Tooling — bending or roll-formingOnly where the section is non-standardQuoted per section, charged onceNot stated here — agreed per projectAdvanced Fabrication HubSection drawing
Material and processingOn order releasePer finished panel, minimum 50 sheets—Global Solution CenterPurchase order

Two of these six lines usually read zero on a first quote, which surprises buyers who expect a tooling charge on every custom job. It should not: 21 finishes and processes are already tooled, from hairline and bead blasted through to water ripple and standard perforation.

What Does a Sample Have to Prove Before a Batch Is Released?

A sample issued before production is the reference the batch is measured against afterwards. It is produced within 48 hours and dispatched within 3 days, usually on the third. That is its whole purpose — not decoration, not a colour card.

Four things are checked. The surface is compared to the approved reference under the same light source the project will be seen in. Flatness is confirmed against the tolerance that applies to that finish. The edge and return are checked for how the material folds. And on patterned work, the pattern position is confirmed so that the joint layout on site matches what was drawn.

Retention matters as much as the approval. A signed sample is kept to judge a repeat order or a replacement panel, which is why the freight is worth paying even though the sample carries no charge.

Need to see a surface before you commit to a batch? Request a sample against your finish specification — we issue it before production and keep the approved reference on file. Request a sample

When Is Tooling Charged — and When Is It Not?

Tooling is a dedicated die, roller, film or plate made so that a specific pattern or section can be produced at all. It is not a service fee, nor a markup on custom work.

It is charged in one case only: when the pattern or the profile does not already exist. A custom embossed texture needs a roller cut. An etched design needs film or a screen made from the artwork. A non-standard hole shape needs a die. A non-standard folded section needs a bending tool or a roll-forming set.

Table 2 — Where tooling physically lands, by process
ProcessWhat the tooling isCharged when
Physical embossingEmbossing roller for the textureNew texture only — water ripple, hammered and linen rollers already exist
EtchingFilm or screen made from the artworkNew artwork only
Artistic perforationDie for a non-standard hole shapeNon-standard hole geometry only
Non-standard section or returnDedicated bending tool or roll-forming setSection outside the standard range only
Print transferPlate made from the pattern fileNew pattern only

The commercial shape is simple, and it is the sentence to hold when a quote looks unfamiliar: tooling is quoted per pattern, charged once, and does not repeat per batch. A 900 m² elevation in a bespoke texture carries the same roller whether it ships in one release or four.

That is also the reason the minimum order exists. Tooling cost per square metre falls as the batch grows, so a short run makes the same roller a much larger share of each panel. The two numbers are a single decision, not two.

What Counts as One Sheet Towards the 50-Sheet Minimum?

The honest answer is that a sheet is a unit of area and gauge, not a fixed quantity of metal, and that is why the question gets asked at all.

Fifty sheets at 1,000 × 2,000 mm is 100 m² of surface. The same fifty at 1,500 × 3,000 mm is 225 m². On a 0.8 mm gauge the first is roughly 0.63 t of steel and the second roughly 1.4 t; at 3.0 mm the same counts are four times heavier.

That is also why the minimum is set against each specification rather than against the order total. Each line has to carry its own setup and its own finishing batch, so sixty sheets spread across six lines is not one order — it is six short ones.

Table 3 — How the 50-sheet minimum is counted
QuestionAnswerWorked example
What the minimum applies toEach specification on the order, not the order totalThree finishes across two gauges is six specifications, each with its own 50 sheets
What counts as one specificationOne finish at one gauge, called out as its own lineHairline at 1.2 mm and hairline at 1.5 mm are two specifications, not one
What that adds up to50 × 6 = 300 sheets before the last line can be releasedA six-line schedule of 60 sheets is not a smaller order; it is six short ones
Why the minimum sits at 50Each line needs its own setup pass and its own finishing batchColour and gloss hold within a batch, so they cannot be borrowed across lines
What to do if one line falls shortConsolidate at drawing stage, or fold that finish into a line already releasedRedrawing is cheaper than running a line below the minimum

The practical consequence is worth stating plainly: a schedule that mixes finishes is a schedule of several minimums. Consolidating two similar finishes at drawing stage is usually the cheapest way to bring a small elevation inside the order, and it is decided long before a purchase order exists.

How Do Panel Size and Tolerance Change What You Can Order?

Format and tolerance are what turn a sheet count into a fabrication scope. The table below is the range every quote is written against, and each line changes either the price or the minimum.

Table 4 — Standard specification and tolerance for quoted panels
ParameterRange or valueWhat it changes in the order
Substrate304 / 316L / 201Grade decides coastal suitability — PREN about 25 for 316L against about 19 for 304
Thickness0.3–3.0 mmGauge change is a separate finishing pass, so it is a separate line
Width10–1,500 mmWider panels reduce joint count but raise yield loss on narrow walls
Length300–6,000 mmFull-height panels remove horizontal joints and increase handling cost
Thickness tolerance±0.01 mmTighter than mill tolerance, so it is a fabrication commitment, not a mill one
Width and length tolerance−0 / +0.2 mmOnly positive, so a cut panel can never come in undersized on site
Flatness≤3 mm general; ≤10 mm for embossed and perforatedTexture and open area relax flatness — expecting 3 mm on water ripple is not achievable
Fire ratingA1 to GB 8624 and EN 13501-1; Class A to ASTM E84Panel rating only; the assembly is assessed separately
PackingPVC film, waterproof paper, wooden crateCrate volume drives freight, and it is part of what the quote covers

The thickness tolerance is the line buyers misread most often. A mill ships to its own tolerance band on a 3.0 mm sheet; holding ±0.01 mm afterwards is a fabrication step, and it is the reason a formed panel fits a drawn rebate without site adjustment.

Flatness is the second. Mirror and hairline are held to 3 mm across the panel. Water ripple, hammered, linen and 3D embossing are held to 10 mm, because the surface itself rises and falls and a 3 mm reading would condemn a correct panel.

What Do A1 Fire Rating and Packing Add to the Quote?

The fire rating adds testing and documentation, not material. Panels are rated A1 to GB 8624 and EN 13501-1, and Class A to ASTM E84 under the American classification, with test reports available on request.

One distinction matters when this line reaches a specifier. A1 describes the panel. The wall or ceiling assembly that the panel is fixed to is assessed as a system, and its result depends on the substrate, the cavity and the fixing. Writing A1 for the panel and claiming it for the assembly is the most common compliance error in a stainless submission.

Packing is quoted as three layers: PVC film on the face, waterproof paper around the bundle, and a wooden crate. The film is transit protection rather than a weathering membrane, so it comes off once the panel is fixed — leaving it on under strong sun is how adhesive residue becomes a site complaint.

Can Tooling Be Reused on a Repeat Order?

Yes, for the same pattern. The roller, die, film or bending tool that was made for the first order still exists afterwards, so a repeat of the identical pattern does not need a second one.

What does need new tooling is any change to the pattern itself: a different hole pitch, a redrawn etched line, a texture at a new scale, a section that moves by even a few millimetres. Those are new tools, because the geometry they cut is different.

This is where custom stainless steel fabrication differs from buying stock sheet. The first order carries the tool; every later order of the same pattern carries only material and processing — which is why the pattern should be frozen as early as the drawing allows.

How Should MOQ Be Written into a Shop Drawing Submission?

Write the quantity and the definition on the same line, and never let the number stand alone. A submission that says 50 sheets without saying what a line covers will be quoted against whichever reading the estimator uses.

Six things belong in the schedule: finish and gauge per line, panel size, the quantity per line, the flatness class that applies to that finish, the substrate grade, and the standard the sheet is ordered to — ASTM A480 or EN 10088-2 are the two that appear most often in architectural specifications.

Add the trim assumption explicitly. A 1,500 mm wide panel cut from a coil has an edge allowance; unstated, the delivered area differs from the ordered area by a margin nobody agreed.

Send the schedule with the drawings. MetalMagus, an architectural stainless steel systems manufacturer, reviews quantity, gauge and finish line by line and returns the open points before quoting. See how a project is processed

What Should a Buyer Ask Before Accepting an MOQ Figure?

Six questions settle whether a minimum order figure is real or provisional.

  • Is the minimum counted per finish and gauge, or across the whole order?
  • Which finishes on this schedule are already tooled, and which need new tooling?
  • Is the sample free, and who pays the freight?
  • Is the tooling charge one-time, and does it appear again on a repeat order?
  • What flatness class applies to each finish on this schedule?
  • Which standard is the sheet ordered to, and which certificate travels with it?

A supplier who answers all six in writing has given you a quotable scope. A supplier who answers only the first has given you a number, and the remaining five will surface later, usually after the purchase order is signed.

Frequently Asked Questions

Is sampling really free?

Yes. Making the sample carries no charge. The freight is on a collect basis, because the courier account and the delivery address belong to the buyer. We issue the sample before production and keep the approved reference on file for later batches.

What exactly is a tooling fee on stainless steel panels?

It is the cost of the dedicated die, roller, film or bending tool needed to produce a pattern or section that does not exist yet. It is not a service charge and not a markup. On the 21 finishes and processes already tooled, it does not arise at all.

Why is the minimum 50 sheets?

Because below that, setup cost per panel rises faster than the price a buyer will accept, and the batch becomes too short to hold one consistent surface across the delivery. Fifty sheets is the point where a finishing line and a forming line can both be set up sensibly.

Does tooling repeat on every order?

No. It is quoted per pattern, charged once, and does not repeat per batch. A repeat order in the identical pattern carries material and processing only. A changed pattern is a new tool, because the geometry it cuts is different.

Can I order below 50 sheets?

Panel size changes what 50 sheets represents, so the practical question is area rather than count. Fifty sheets at 1,000 × 2,000 mm is 100 m²; at 1,500 × 3,000 mm it is 225 m². Where a single line is genuinely small, the cheaper route is to consolidate it with a similar finish at drawing stage rather than to run it below the minimum.

Is the minimum counted per finish or across the order?

Per finish and gauge, not across the order. A schedule with three finishes across two gauges is six specifications, each carrying its own 50 sheets, so it holds 300 sheets before the last line can be released. Consolidating two similar finishes at drawing stage is what brings a small elevation inside the order.

Does MOQ change with panel size?

The count does not, but the area and the tonnage behind it do. At 3.0 mm the same fifty sheets are four times the weight of 0.8 mm. That is why a quote should state format and gauge next to the quantity, not only the quantity.

What is the production lead time?

Standard production ships in 20 working days. It is a planning figure, not a fixed date: tooling, the finish on each line and the quantity behind it all move it. The release date is confirmed per order, in writing, before the purchase order.

What does the sample not prove?

It does not prove assembly performance. Fire rating, acoustic behaviour and wind load belong to the wall or ceiling build-up, not to the panel alone. Those are assessed as a system, and the reports are available on request.

MetalMagus, an architectural stainless steel systems manufacturer, quotes sampling, tooling and the order as three separate lines for custom stainless steel fabrication, so that none of them hides inside another. If the schedule is still open, send the elevation and the finish intent — the quantity question is easier to settle on a drawing than in an email.

About the author

By the Project Management Office, MetalMagus — the team that converts a drawing set into a costed, buildable order. It owns the quantity definitions, the tooling decision and the schedule that goes back to the buyer, and it signs off the commercial terms behind every quote.

Are you looking for a reliable manufacturer?

We can quickly provide customers with market analysis, technical support and customized services.