Experts in high-end stainless steel for architectural aesthetics and spatial art solutions.

Home / All / Specification & Selection / Factory vs Trading Company for Stainless Cladding: What the Documents Should Show

Factory vs Trading Company for Stainless Cladding: What the Documents Should Show

Nov 12,2026
Contents9 sections
Quick Answer

A trading company can sell good panels; the risk is what happens when a batch is wrong. Ask for the melt certificate with the heat number, the workshop that formed the panel, the release sheet signed by whoever measured it, and a remake clause with a date. Three of those four without a name means you are buying a promise.

What Is Actually Different Between a Factory and a Trader?

The difference is not quality. A trader with a good fabricator behind it can deliver a better panel than a factory having a bad month. The difference is who owns the process when something goes wrong — who still has the sheet, who can remake it, and who has to answer for the measurement.

That ownership shows up in four places, and none of them is a brochure. It shows in whether the business licence carries a manufacturing scope or a trading scope. It shows in whether the person who signs the inspection release is employed where the panels were made. It shows in whether a shop drawing exists before the panel does. And it shows in what the contract says about a remake, and by when.

MetalMagus(杭州新恒裕不锈钢制品有限公司)is a fabricator, which means the sheet in the yard, the polishing line, the press and the crating bench are in one place — 58,000 m² of it. That does not make every trader unreliable, and it does not make every factory reliable. It does mean that for our own work, the chain of custody runs from coil to crate without a handover, so a document either matches the material or the mismatch is visible in the same building.

For a buyer, the useful question is not "are you a factory". It is "which of these four documents can you produce, from your own records, this week". A trader who can produce all four is a lower risk than a factory that cannot produce two.

Which Documents Cannot Be Borrowed?

Four documents cannot be borrowed honestly, because each one is tied to a specific piece of material or a specific person. Everything else — a brochure, a catalogue, a project list, a video — can be assembled by anyone.

The melt certificate carries a heat number, and that heat number has to match the tag on the bundle in the yard. A certificate without a matching tag proves that a mill once made some 316L, not that this sheet is 316L.

The shop drawing has to have been produced by the party that will fabricate from it. A drawing downloaded from the architect and re-issued under another logo has no resolved corners, no joint build-up and no fixing detail — which is exactly the part that reveals whether the fabricator has done the work before.

The inspection release sheet has to be signed by the person who measured the panel, and it has to carry the numbers they measured. A release sheet that says "passed" is not a record; it is an opinion.

The remake clause has to name a trigger and a date. Without both, the clause exists to be argued about rather than used.

Table 1 — Four documents, what each proves, and how it is commonly substituted
Document What it proves Common substitute Second check
Melt certificate The alloy of this coil, by heat number A grade-name certificate with no heat number Match the heat number on the bundle tag and the packing list
Shop drawing The fabricator has resolved corners, joints and fixings Architect's drawing re-issued under a supplier logo Ask for one detail only they could have drawn — an edge return or a corner build-up
Inspection release sheet Someone measured this panel and signed for the result A stamp saying "passed" with no values Ring the signatory and ask which instrument was used
Remake clause Who pays, and how fast, when a panel is out of specification "Quality guaranteed" with no trigger or date Ask what happens if flatness is 8 mm on an embossed panel with a 10 mm limit but 3 mm written on the drawing

How Do You Read a Melt Certificate?

Read it against the tag, not against the grade name. A melt certificate to EN 10088-2 carries the heat number, the chemical composition, the mechanical properties and the standard the coil was produced to. The composition is where the answer sits: for 316L, molybdenum is the element that matters, and its presence is what lifts PREN to about 25 against 19 for 304.

Three checks take a few minutes. First, the heat number on the certificate must appear on the bundle tag and on the packing list of the shipment you are receiving — not on a certificate emailed separately with no reference. Second, the certificate must name the mill that rolled the coil, not the trader that bought it. Third, the dimensions on the certificate should be consistent with what you ordered: thickness inside 0.3–3.0 mm, width inside 10–1500 mm, length inside 300–6000 mm.

Where a project is coastal, add one more: compare the molybdenum figure against the grade's minimum, not against a typical value. A certificate that reports composition without the standard it is measured to is a data sheet, not a certificate.

Why Does the Release Sheet Name a Person?

Because accountability has to attach to someone who can be asked a question. A release sheet names the inspector, the date, the panel reference and the measured values: thickness against ±0.01 mm, width and length against −0/+0.2 mm, flatness against 3 mm Maximum or 10 mm Maximum depending on the process, and the visual check against the approved sample.

That record is also the only way a claim can be settled quickly. If a panel arrives at 6 mm flatness on a brushed surface with a 3 mm limit, the release sheet either shows the deviation was recorded and accepted in writing, or it does not — and the difference between those two situations is the difference between a remake and an argument. MetalMagus, an architectural stainless steel systems manufacturer, releases every panel on that basis.

A trader can supply a release sheet, and it is legitimate when the sheet is signed by the workshop that made the panel and names that workshop. What is not legitimate is a release sheet signed at an office that never saw the panel, on values nobody measured. Ask for the signatory's role in the same email as the document.

A document set is either complete before the deposit or it is assembled afterwards. — Ask for the Document Set

What Does a Remake Clause Need to Say?

Four things, in writing, before the deposit: the trigger, the evidence, the turnaround and the cost split.

The trigger is the measured condition that makes a panel non-conforming, expressed against the same values as the release sheet. "Poor quality" is not a trigger; "flatness above 3 mm Maximum on a brushed panel, measured on a surface plate" is.

The evidence is what the buyer has to provide and what the supplier has to provide — photographs with a straight edge, the measurement record, the retained approved sample. Without an agreed evidence standard, every claim starts from zero.

The turnaround is a date, not a duration in principle. It should say when the replacement panel is dispatched, and what happens to the rest of the order in the meantime.

The cost split covers the panel, the freight and the site cost of refitting. Most disputes are not about whether a panel is wrong; they are about who pays the crane.

The fifth item most clauses omit is who measures. Name the instrument and the party who holds it, otherwise the trigger exists on paper and the measurement happens in an argument on site.

One clause with a date is worth more than a page of warranty language. — Ask for the Document Set

When Is a Trader the Better Choice?

There are real situations where a trader is the better buy, and refusing to admit it is how buyers end up with a package assembled from four factories and coordinated by nobody.

The first is a mixed package. A lobby that needs stainless wall panels, a brass reception desk and an aluminium ceiling is three supply chains. A trader who already handles all three removes three sets of Incoterms, three inspection regimes and three payment paths from your week.

The second is a small quantity. Fifty sheets per specification is a workable minimum for a fabricator, but a project that needs twelve panels in three finishes is below the level where a factory's scheduling attention is reliable. A trader consolidating small lots across projects can move faster than a factory that has to break a line setup.

The third is distance and language. If you cannot visit, and you do not have an inspector, a trader who already sits between the workshop and the export process may be the only party able to chase a crate through a port.

The condition is the same in all three cases: the documents must come from the workshop, and the workshop must be named. A trader who will not name the fabricator is not managing risk; it is transferring it to you.

Table 2 — Which structure suits which purchase, and what to add to the contract
Situation Structure Reason Clause to add
One material, large volume, fixed specification Factory direct Fewest handovers; remake can be scheduled on the same line Release sheet per panel; spares from the same batch
Mixed materials, one delivery window Trader with named workshops One commercial contact, one consolidation point Each workshop named in the annex; certificates from each mill
Small quantity, several finishes Trader or a fabricator's sample line Volume too low to hold a line slot Batch colour reference; dispatch date per finish
Coastal project, no site inspector Factory direct with third-party inspection Grade and finish both need verification at source Inspection right before crating; heat number on packing list

How Do You Audit a Workshop Remotely?

Audit live, not from a file. A recorded video proves that at some point a machine ran; a live call proves that it is running now, with your material on it.

Ask for a walk that follows the material, not the showroom. It starts at coil or sheet storage, where the bundle tag should be visible and readable; moves to the line where the panel is formed, with the job sheet in the operator's hand; continues to the surface area where the finish is applied; and ends at the crating bench, where the packing specification — PVC film, waterproof paper, wooden case — is either being followed or improvised.

Then ask for three measurements on camera. Thickness with a micrometer against ±0.01 mm. Width and length against −0/+0.2 mm. Flatness on a surface plate against 3 mm Maximum, or 10 mm Maximum where the panel is embossed or perforated. A workshop that cannot measure on request is not producing to a specification; it is producing to a habit.

Two red flags are worth more than the rest. A refusal to go live — "our connection is poor, we will send a video" — usually means the address on the licence is not the address of the line. And a machine nameplate that reads narrower than the width being quoted means the panels are being bought in, not made there.

The audit is also where you check that the party answering the email is the party holding the sheet. Ask one question that only the workshop can answer: what gauge is on the line today, and which finish is running after it.

A live walk costs an hour and settles what a brochure cannot. — Ask for the Document Set

What Should Be Written Before the Deposit?

Five items belong in the contract or its annex, and each one closes a specific gap.

The document set, listed by name, with the commitment that each item accompanies the shipment and that the heat numbers on the certificates match the packing list. This turns a good intention into an obligation.

The scope matrix: who supplies the sheet, who forms it, who finishes it, who crates it, who clears it. On a stainless cladding package this matrix is where a trader's real structure becomes visible, because a company that supplies all five columns is a fabricator and a company that supplies two is a coordinator.

The inspection right, stated as a time window before crating, with the buyer's inspector or a third party allowed on the floor. This is the clause that makes every other document enforceable, because it is the one that can be exercised while the panels are still in the building.

The remake clause with its four parts: trigger, evidence, turnaround and cost split. Written against the same numeric values as the release sheet, so that a dispute is a comparison rather than an interpretation.

The packing specification, down to film type, paper, case construction and marking. A1 fire rating belongs on the certificate; the crate belongs on the drawing, because a panel that arrives with a crushed edge is a remake regardless of how good the steel was.

Two quotes that arrive as one figure each cannot be compared, and the cheaper one is usually the one with less written down. Normalise them on six lines before anyone is asked to justify a price: gauge and finish per panel, flatness and roughness class, packing, freight term, tooling position, and whether certificates and the release sheet are included or billed separately. A quote that omits packing and inspection is not cheaper; it is a quote for a different job, and the difference returns as a claim rather than an invoice.

MetalMagus, an architectural stainless steel systems manufacturer, quotes cladding packages against this document set rather than against a price alone. That is not a claim that a factory is always the right answer — it is a claim that the answer should be visible before the money moves.

Where the package also includes interior work, the same document logic applies to wall panel systems and to exterior envelopes such as a flat minimal facade. For a fabricator, the interesting document is the same in both cases: a shop drawing that resolves the corner before the panel is cut. Our own custom stainless steel fabrication runs from coil to crate in one plant, and roofing work such as standing seam stainless roofing is quoted on the same basis.

Frequently Asked Questions

Is a trading company always riskier than a factory?

No. The risk is not the structure; it is the missing name. A trader who names the workshop, supplies that workshop's release sheet, and carries a remake clause with a date is a controlled risk. A factory that cannot produce a heat-numbered certificate or a measured release sheet is a larger risk, because you have no document to act on when something arrives wrong.

What is the single most useful document to ask for first?

The melt certificate with a heat number that appears on the bundle tag. It is the only document that ties the alloy to the actual sheet you are buying, and it is hard to borrow honestly. Everything else can be assembled by a competent office; a heat number either matches the material in the yard or it does not.

How can I tell a shop drawing from an architect's drawing?

A shop drawing resolves something. Look for the corner build-up, the edge return, the joint width with its tolerance, and the fixing detail with its movement allowance. An architect's drawing that has been re-issued under a supplier's logo usually stops at the panel edge, because the party that re-issued it did not do the detailing.

Is a release sheet without measured values acceptable?

No. A release sheet is a record of measurement, so it needs the instrument, the values and the name of the person who took them. Thickness against ±0.01 mm, width and length against −0/+0.2 mm, flatness against 3 mm or 10 mm Maximum depending on the process. A stamp that says "passed" is an opinion, and it cannot settle a claim.

Can a trader issue a legitimate release sheet?

Yes, if it is the workshop's sheet that carries the values and the inspector's name, and if the workshop is named in the annex. What is not legitimate is a sheet signed at an office that never saw the panel. Ask for the signatory's role and the workshop address in the same email.

What should a remake clause actually say?

Four things: the trigger as a measured condition, the evidence standard, the dispatch date for the replacement, and who pays for the panel, the freight and the site cost of refitting. Most disputes are not about whether a panel is wrong but about who pays the crane, so put that in the clause rather than discovering it later.

When is a trader genuinely the better choice?

On a mixed package with several materials and one delivery window, on a small quantity spread across several finishes, and where the buyer has no inspector and needs someone to chase a crate through a port. In each case the condition is the same: the workshops are named and the documents come from them.

What should I ask for in a remote factory audit?

A live walk that follows the material: coil storage with readable tags, the line with the job sheet, the finishing area, and the crating bench. Then three measurements on camera. Refusals to go live, and machine nameplates narrower than the width being quoted, are the two signals worth acting on.

Does the country of the workshop matter more than the structure?

Less than the documents. A workshop that measures, signs and remakes is a workable supplier wherever it sits; a workshop that does none of those is not improved by being close to you. What the country changes is the cost of a remake and the time it takes, which is why the dispatch date matters as much as the trigger.

What should be in writing before the deposit?

The named document set with heat numbers on the packing list, the scope matrix showing who supplies and who forms, the inspection right before crating, the four-part remake clause, and the packing specification down to film and case. Five items, all short, all checkable at the end of the job.

4Documents that cannot be borrowed
0.3–3.0 mmSheet thickness
±0.01 mmThickness tolerance
A1Fire rating, GB 8624

Are you looking for a reliable manufacturer?

We can quickly provide customers with market analysis, technical support and customized services.